New Genius obd ii/boot master review:
Two months ago I ordered a New Genius 5.05 K-Touch Map online. Now I want to share my experience of Chinese New Genius with you all, so post my real feedback here.
claims this New Genius K-Touch is the first Touch Map device which can read and program the ECU in modern vehicles over OBD2. Yep, as it advertised. In garage I tested it ok to read/write ECU on these vehicles:
2014 Ford Fiesta Ecoboost 1.0 125hp auto
2013 Mitsubishi ASX/Outlander Sport 2.0 4B11 CVT
2014 Chevrolet Orlando 1.8 Petrol Auto
2015 Mitsubishi Montero Sport/Pajero Sport 2.5DiD 178hp auto
Opel Zafira , Combo , Meriva Denso
Mercedes EDC16C2 ID
How I use New Genius to remap and tuning ECU?
I read data through OBD and save file to device. Then connect with this k- touch program and export file to pc. Before tuning I use gen file extract (the original genius file). After tuning I import file to device with k-touch program and write the file to car.
P.S need DS manager device to do this.
It also claims New genius obd ii/boot master is updated version of Kess V2 and support more new vehicles. In my view, New Genius K-Touch =Laptop +Kess V2. More support vehicles I didn’t test all, but I am sure Kess cannot do Mitsubishi while New Genius can.
About Difference between New Genius and Kess V2, I found this table on eobdtool.co.uk website. By the way, I ordered New Genius from this website and got an Fgtech Galletto V50 additionally for Free.
Check this link if you need:
| Product Name | New Genius | Kess V2(SE87-C) | Kess V2(SE87-D) |
| Language | English, Italian, German, French, Spanish, Portuguese, Hungarian | English, German, Spanish, Italian, Portuguese, French | English, German, Spanish, Italian, Portuguese, French |
| Software | -- | V2.15 | V2.15 |
| Hardware | V5.005.003 | V4.036 | V4.036 |
| Tokens | No Tokens Limitation,30 Tokens come with device by default, you can press the tokens reset button on the back of hardware to get new Tokens | No Tokens Limitation,CD comes with token programmer, you can follow our video to program tokens. No need remove chips or desolder chips | No Tokens Limitation there is renew button on the main unit. This button is used to charge tokens. Once your tokens run over, just click this button, then tokens will go back to 30 tokens. |
| Update | via hardware | via hardware | via hardware |
| Support Protocols | upports CAN-BUS, KWP and J1850 protocols | Line, CAN, EDC17 and MED17 and Ford J1850 | Line, CAN, EDC17 and MED17 and Ford J1850 |
| Support Vehicle | Car, Bikes, LCV Support more new vehicle than Kess V2 New Genius ECU List | Car and Bike | Car and Bike |
| PC | Hand-held ECU Chip Tuning Tool, no PC need when you read and write ECU data; but you need install K-touch software to export and import ECU data | PC-based ECU Programmer, you need install the software by yourself | PC-based ECU Programmer, you need install the software by yourself |
| Method | Read and Write ECU via OBD2 directly | same | same |
When using New Genius K-Touch I met two troubles finally solved (got technical help online form www.eobdtool.co.uk), in case you may meet them as well I summarized two using tips for you:
- Some of you may also fail to use New Genius to do DQ250/DQ500.
Solution: simply connect a 120R resistance between CAN High and CAN Low, when you connect OBD.
- I knew this New Genius is without token limitation, so I tried to press the tokens recovery button to recovery tokens, but the light kept flashing. I tested the button and find it not working with home version change but no token.
Solution: There are 2 switches at the bottom press the switch nearest LED on top, went back up to 30, press and hold switch, apply power, waited 10 seconds pulled power out and removed clip.
This
is from EOBDTOOL website
technical support:
没有评论:
发表评论